#4 LH Armstrong bandsaw grinder with Digicam. The customer has the Digicam software disk for the grinder.

New Simmonds Blades included. John Deer 4045TF150 engine. Hours unknown. Engine is clean and runs well.

2021 Bandit 3680T Wood Grinder -147 Hours -5 Year CAT Warranty -Excellent Condition - More photos and info coming.

Bandit Chipper with hydraulic dumping hopper 3-cylinder Deutz air cooled engine New hoses and freshly painted

CBI 400 Grinder

Nice Newman G-280 tub grinder. Everything functional just needs cleaned.

Nice Newman G-280 that has been refreshed. Has extra cylinder wheels that come with it.

Very clean Newman G-200 Knife grinder. In good working order, grinds 17" on the inside and 20" on the outside.

Complete Chip Mill that is ready to be moved System includes: - Log Deck - Log Singulator - Control Room - Nicholson A5 Debarker - Peeled Log Outfeed Bin - Reclaim Log Infeed Deck - Bark conveyor and stacker - Bark Shredder - Progress 84" 6 Knife Chipper w/ 600 HP Motor - Progress Chip Screen: 7'x14' - Chip Blower and Truck Loading Conveyor - MCC Center

Nicholson Flat Drum Chipper 9'5' x 55" Includes: Trailer, AC power, belt conveyor, switch gear option. System chipped just over 120 truckloads

The seller has confirmed that this 96" Precision chipper is in good working/running condition and is ready to load. This was not heavily run. This came out of a chip plant in WA. Model 96.27 - Horizontal feed - Side discharge - 4-Knife whole log chipper - 8" thick chipper dissc - Built in disc brake - Extended front shaft for hydraulic starter - Hydraulic starting motor - Side discharge pipe with motorized outlet adjustment - 27" maximum log diameter - Many spare parts and knives included - Average production rate: 125 tons per hour - No hydraulic pump - No motor - an 800HP one can be added for additional cost though... The photo's show the optional extended shaft and hydraulic starting motor which is a special feature....

Complete chip plant includes: - The infeed is 12’ above ground level. They were feeding it one log at a time with a shovel. - There is a single chain 12” wide leading to the debarker. - The debarker is a Salem 20” ring debarker with mcdiarmond controls. - From the debarker it goes through I think is a metal detector. It’s is enclosed, 8’ long with a belt conveyor. - 75’ of 3-strand chain that reduces to 2-strand chain for 35’ then goes to another 2-strand chain for 12’ then goes into the chipper. - The chipper is a Precision with 2- 400 hp high efficiency 3 phase motors. - From the chipper the chips drop onto a 42”x50’ inclined belt that leads to the 2 deck screen. The screen is 92”x20’ - The waste goes on a 9”x20’ incline belt and dropped into a truck. - The chips go out on a 3-strand 100’ conveyor (strands are 14” wide) to a radial stacker for loading trucks. The stacker belt is 42”x65’ - Chips can be redirected to blower unit system that will transport them to a rail siding to so they can be loaded into a rail area. It starts out with 75’ of 12” pipe running on the ground. Then it sweeps straight up to a height of about 24’ and goes 150’ to a siding across the county road. The chip loading facility is intact. - The hog is located back by where the logs are loaded onto the chain going to debarker. Here’s a list of the conveyors going back to the Kockums hog. It has a 24”x36” opening at the top. - Conveyors: 12”x100’, 12”x 25’, 12”x60’. All of these conveyors are 1 strand steel.

Precision 58" Chip Pac 6-Knives 72" Cyclone H-Type blower with dual load out chutes 6'x6' Screen 25' Vibrating Infeed with transition chute to chipper with fiberglass section and MDI metal detector

Precision 58" Chipper - Model 58-60-16 6 Knife 150 HP Motor

Rotochopper MC256 3126B 300 Hp CAT Engine Dust Control 60 Teeth Roto902 8 row rotor 3/4 x 2 1/4 bolts 3 button remote-Elec Sol Model EL24VRT Drive Belt BL10/5V1600 Square D buttons on 3 button box 24 Volt System Radiator PreCleaner CAT radiator CAT Alternator 9X7803 Turbo II 68-6 intake S/N 87384 DT motors w/case drain Hyd Screen changer Hyd Valve Ass'y Hyd Actuator Hyd powerfeed shock kit Magnet Long Conveyor Pintle Hitch 3 15/16" FAG main rotor bearings Smooth underrotor belt R2 lacing 3/8" steel infeed belt 2 7/16" bearings and shaft on infeed Slab ramp w/blocks No flip down sides on infeed AW68 hyd oil Gruber Welding fuel & oil tank BEE70 omega coupler 3/4" baffled screen Will need to be moved on a trailer.

Soderhamn 48" Chipper M671 Diesel Engine Mounted on trailer

Recently removed from service Available immediately